Различия
Здесь показаны различия между двумя версиями данной страницы.
| Предыдущая версия справа и слева Предыдущая версия Следующая версия | Предыдущая версия | ||
|
doc:jroboplc:modules:peripherial:omronv7 [2015/12/21 11:54] denis [Регистры] |
— (текущий) | ||
|---|---|---|---|
| Строка 1: | Строка 1: | ||
| - | ====== omron.v7 ====== | ||
| - | Частотный преобразователь Omron V7. | ||
| - | |||
| - | Используемый протокол - MODBUS. | ||
| - | |||
| - | http://www.omronkft.hu/nostree/pdfs/inverter/cimr-v7az/v7az.pdf | ||
| - | |||
| - | |||
| - | <code yaml> | ||
| - | plugin.peripherial: | ||
| - | |||
| - | module.icp1: | ||
| - | portnum: 2 | ||
| - | netaddr: 1 | ||
| - | enable: on | ||
| - | type: omron.v7 | ||
| - | </code> | ||
| - | |||
| - | |||
| - | ==== Регистры ==== | ||
| - | |||
| - | * **Reg0001** | ||
| - | * 0 Run Command - 1: Run, 0: Stop | ||
| - | * 1 Reverse Run Command 1: Reverse run 0: Forward run | ||
| - | * 2 External fault 1: Fault (EFO) | ||
| - | * 3 Fault Reset Command 1: Reset Command | ||
| - | * 4 Multi-function input reference 1 (Function selected by n050) | ||
| - | * 5 Multi-function input reference 2 (Function selected by n051) | ||
| - | * 6 Multi-function input reference 3 (Function selected by n052) | ||
| - | * 7 Multi-function input reference 4 (Function selected by n053) | ||
| - | * 8 Multi-function input reference 5 (Function selected by n054) | ||
| - | * 9 Multi-function input reference 6 (Function selected by n055) | ||
| - | * A Multi-function input reference 7 (Function selected by n056) | ||
| - | * B-F (Not used) | ||
| - | * **Reg0002** - Frequency reference (unit: n152) | ||
| - | * **Reg0020** - Status signal | ||
| - | * 0 Run Command 1: Run 0: Stop | ||
| - | * 1 Reverse Run Command 1: Reverse run 0: Forward run | ||
| - | * 2 Inverter operation ready 1: Ready 0: Not ready | ||
| - | * 3 Fault 1: Fault | ||
| - | * 4 Data setting error 1: Error | ||
| - | * 5 Multi-function output 1 (1: MA ON 0: MA OFF) | ||
| - | * 6 Multi-function output 2 (1: P1 ON 0: P1 OFF) | ||
| - | * 7 Multi-function output 3 (1: P2 ON 0: P2 OFF) | ||
| - | * 8-F (Not used) | ||
| - | * **Reg0021** - Fault description | ||
| - | * 0 Overcurrent (OC) | ||
| - | * 1 Overvoltage (OV) | ||
| - | * 2 Inverter overload (OL2) | ||
| - | * 3 Inverter overheat (OH) | ||
| - | * 4 (Not used) | ||
| - | * 5 (Not used) | ||
| - | * 6 PID feedback loss (FbL) | ||
| - | * 7 External fault (EF, EFO), Emergency stop (STP) | ||
| - | * 8 Hardware fault (FXX) | ||
| - | * 9 Motor overload (OL1) | ||
| - | * A Overtorque detection (OL3) | ||
| - | * B Undertorque detection (UL3) | ||
| - | * C Power loss (UV1) | ||
| - | * D Control power fault (UV2) | ||
| - | * E MEMOBUS communications timeover (CE) | ||
| - | * F Operator connection fault (OPR | ||
| - | * **Reg0022** - Data link status | ||
| - | * 0 Data write in | ||
| - | * 1 (Not used) | ||
| - | * 2 (Not used) | ||
| - | * 3 Upper/lower limit fault | ||
| - | * 4 Consistency fault | ||
| - | * 5-F (Not used) | ||
| - | * **Reg0023** - Frequency reference (unit: n152) | ||
| - | * **Reg0024** - Output frequency (unit: n152) | ||
| - | * **Reg0027** - Output current (10/1 A) | ||
| - | * **Reg0028** - Output voltage reference (1/1 V) | ||
| - | * **Reg0029** - Fault description | ||
| - | * 0 (Not used) | ||
| - | * 1 (Not used) | ||
| - | * 2 Input open phase (PF) | ||
| - | * 3 Output open phase (LF) | ||
| - | * 4-F (Not used) | ||
| - | * **Reg002A** - Alarm description | ||
| - | * 0 Operation function stop (STP) | ||
| - | * 1 Sequence error (SER) | ||
| - | * 2 Simultaneous FWD/REV Run Commands (EF) | ||
| - | * 3 External Baseblock (BB) | ||
| - | * 4 Overtorque detection (OL3) | ||
| - | * 5 Cooling fan overheat (OH) | ||
| - | * 6 Main circuit overvoltage (OV) | ||
| - | * 7 Main circuit undervoltage (UV) | ||
| - | * 8 Cooling fan fault (FAN) | ||
| - | * 9 Communications fault (CE) | ||
| - | * A Option card communications error (BUS) | ||
| - | * B Undertorque (UL3) | ||
| - | * C Inverter overheat alert (OH3) | ||
| - | * D PID feedback loss (FBL) | ||
| - | * E Emergency stop (STP) | ||
| - | * F Communications waiting (CAL) | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | ===== Теги ===== | ||
| - | |||
| - | |||
| - | <code> | ||
| - | Reg0001 | ||
| - | Reg0002 | ||
| - | Reg0020 | ||
| - | Reg0021 | ||
| - | Reg0022 | ||
| - | Reg0023 | ||
| - | Reg0024 | ||
| - | Reg0027 | ||
| - | Reg0028 | ||
| - | Reg0029 | ||
| - | Reg002A | ||
| - | |||
| - | SYSTEM.ErrorCount | ||
| - | SYSTEM.ErrorFlag | ||
| - | SYSTEM.NetAddr | ||
| - | SYSTEM.Port | ||
| - | SYSTEM.TimePeriod | ||
| - | SYSTEM.UpdateDate | ||
| - | SYSTEM.UpdateTime | ||
| - | |||
| - | </code> | ||
| - | |||
| - | |||
